<dd id="juqeb"><optgroup id="juqeb"></optgroup></dd>

    1. <ol id="juqeb"></ol><em id="juqeb"><acronym id="juqeb"><input id="juqeb"></input></acronym></em>
    2. <em id="juqeb"></em>
    3. <dd id="juqeb"><pre id="juqeb"></pre></dd>
            產品列表
      路沿石鋼模具
      蓋板鋼模具
      標志樁鋼模具
      隔離墩鋼模具
      化糞池鋼模具
      U型槽鋼模具
      遮板鋼模具
      道軌模具
      護坡鋼模具
      制磚機
      檢查井鋼模具
      聲屏障鋼模具
      防撞墻鋼模具
      圍墻板模具
      方涵模具
      錨桿框架梁模具
      配重塊模具
      水泥三盤模具
      水泥預制件模具
            新聞中心
      · 整體式檢查井模具的作用及結...
      · 水泥檢查井模具的優勢特點
      · 觀察井模具的結構及特點
      · 檢查井模具的規格、尺寸、特...
      · 路面板模具在道路施工中的重...
      · 裝配式路面板模具的施工方式
            聯系我們

      電話:0312-8103818 18803129528
      傳真:0312-8103818
      在線QQ:107108222
      地址:保定市城東工業區

           新聞中心

      U型槽模具的施工方法

      [關閉該頁][設為首頁][添加收藏][發送朋友][打印][ ]

            U型槽模具有兩種材質,一種是塑料的,另一種是用鋼板焊接建造的,U型槽模具具有堅固耐用的特點,而且同其他材料相比,他具有節省鋼材,成本更低等優點。由于U型槽都是一些水泥制品,其壓力大重量大,所以在選用的時候鋼板厚度需要注意,U型槽鋼模具的尺寸規格有經常使用的幾種,同時這種U型槽尺寸規格小的可以選用薄一點的鋼材,超過1米的模具在使用薄的鋼材比較不合適,應該選用5MM厚一點的鋼材,選用鋼模具生產能夠降低一定的生產困難,同時這種鋼模具使用壽命很長,可以大大的提升產品的生產效率。

      There are two kinds of materials for U-groove die, one is plastic, the other is welded with steel plate. The U-groove die has the characteristics of ruggedness and durability. Compared with other materials, it has the advantages of saving steel and lower cost. Because U-groove is some cement products, its pressure is large and its weight is heavy, so the thickness of steel plate should be noticed when choosing. The size specifications of U-groove steel die have several kinds that are often used. At the same time, the size specifications of U-groove steel can be selected to be a little thinner. Dies over 1 meter are not suitable for using thin steel. Steel with a thickness of 5MM should be selected and steel die should be selected. Production can reduce certain production difficulties, at the same time, the service life of this steel die is very long, which can greatly improve the production efficiency of products.

           一般U型槽模具是u型槽預制成型,如果使用在一些大型建筑物底部支撐的作用,根據使用的u型槽模具尺寸調整,首先,會增加鋼板的厚度,然后將增加鋼板的寬度,通常我們使用u型槽在高速公路上的鋼板厚度,模具是在2 - 4厘米,寬度在500x400,規范也非常多,所以的厚度大的u型槽鋼模具將在3到5厘米,用于大型的建設好,獨立橋墩磚的工作由原位生產方式,現在很多施工現場的方法,和一些生產方法是建設單一鋼鐵架標簽的位置,然后在鋼管的支持,然后在模板上的接頭,內和外板,焊接,將所有的焊接螺釘孔和加強筋,然后灌澆混凝土。這些程序之前組裝后的鋼板,中間的板的安裝,中間有設置自動扶梯或電梯,方便施工人員及時容易去除內部脫模模板。

      Usually U-groove die is prefabricated u-groove. If it is used to support the bottom of some large buildings, it can be adjusted according to the size of U-groove die. First, the thickness of steel plate will be increased, and then the width of steel plate will be increased. Usually, we use U-groove in the thickness of steel plate on expressway. The die is 2-4 cm, the width is 500 x 400, and there are many specifications. The thick U-shaped channel steel die will be used for large-scale construction. The work of independent pier bricks will be done by in-situ production. Now many construction site methods and some production methods are to construct the location of a single steel frame label, then support the steel pipe, then weld the joints on the template, the inner and outer plates, weld all the welding screw holes and reinforcement bars, and then pour and mix them. Condensate. These procedures are assembled before the steel plate, the installation of the middle plate, and the installation of escalators or elevators in the middle. It is convenient for the construction personnel to remove the internal demoulding template in time and easily.


      【上一個】 檢查井模具的獨特設計均可定做 【下一個】 隔離墩模具的巧妙設計及防撞功能


       · U型槽模具的施工方法

      檢查井鋼模具,檢查井模具,水泥檢查井模具——保定市晨澤模具制造有限公司 |隔離墩模具|排水溝模具|
      久久久噜噜噜久久熟女色_国产在线jyzzjyzz免费_2020国产情侣在线视频播放_8050二级一级全黄