檢查井鋼模具在生產完成之后需要運送給施工方，然后施工方再使用該模具去進行混凝土檢查井預制件的生產，那么究竟如何去使用檢查井鋼模具呢？首先需要對混凝土檢查井模具進行檢查，看看是否該模具的結構方面符合客戶的要求，然后就要在模具與泥漿接觸的地方涂上脫模劑，這是為了避免泥漿粘連在模具上，也是為了之后的脫模更加方便。刷完脫模劑之后就可以往模具里面澆灌上大量的混凝土，另外需要注意的是因為混凝土檢查井模具體積較大，所以是不可能將這種模具搬運到震動平臺上進行震動的，這時候就可以使用到震動棒進行震動，將震動棒插入到混凝土里進行均勻震動，這樣做的目的是為了能夠讓模具里面的氣泡快速的排出來，在檢查井預制件使用的時候不會影響到其使用效果。在震動完成之后就要等待混凝土晾曬風干，等模具里面的混凝土凝固好了之后就可以開始脫模了，這樣一個成型的混凝土檢查井預制件就生產出來了。
After the completion of the production, the steel mould of the inspection well needs to be delivered to the construction party, and then the construction party uses the mold to produce the prefabricated parts of the concrete inspection well. How to use the mold? First of all, it is necessary to check the mold of the concrete inspection well to see whether the structure of the mold meets the requirements of the customer. Then, the mold release agent should be applied at the place where the mold contacts with the mud. This is to avoid the mud sticking on the mold, and also to facilitate the subsequent demoulding. After brushing the release agent, a large amount of concrete can be poured into the mold. In addition, it should be noted that because the mold volume of the concrete inspection well is large, it is impossible to transport the mold to the vibration platform for vibration. At this time, the vibrator can be used to vibrate and insert the vibrator into the concrete for uniform vibration. The purpose of this is to It can make the bubbles in the mold quickly discharged, and the use effect will not be affected when the prefabricated parts of the inspection well are used. After the vibration is completed, it is necessary to wait for the concrete to dry in the air. After the concrete in the mold is solidified, the demoulding can be started. Thus, a prefabricated concrete inspection well is produced.
檢查井鋼模具使用的是優質的水泥,將其放入模具中振動擠壓成型,在這個過程當中,模具是通過內膜的振動效果和幅度進行調整,用更好的震動了使得水泥更加密實,得到一個質量穩定性更好的預制件,這種模具的保護層比較均勻,焊接密度較高,不會出現離心、跳筋等現象,保障了模具在使用的過程中不會對水泥的規格尺寸造成影響,使用壽命比較長。檢查井鋼模具運用了厚度足夠的鋼面板焊接,按照圖紙調節好角度,讓模具的整體性更強。檢查井鋼模具是一種可以循環使用的鋼模板,而且每套模具的使用年限可以達到3年以上。
High quality cement is used in the inspection well steel mold, which is put into the mold for vibration extrusion molding. In this process, the mold is adjusted through the vibration effect and amplitude of the inner membrane. The better vibration makes the cement more dense, and a prefabricated part with better quality stability is obtained. The protective layer of this mold is relatively uniform and the welding density is high, There will be no centrifugal, jump reinforcement and other phenomena, to ensure that the mold will not affect the specification and size of cement in the process of use, and the service life is relatively long. The inspection well steel mold uses the steel panel welding with enough thickness, and adjusts the angle according to the drawing, so that the integrity of the die is stronger. Inspection well steel mold is a kind of steel formwork which can be recycled, and the service life of each set of mold can reach more than 3 years.
打印